Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen gezeigt.
Beide Seiten, vorherige Überarbeitung Vorherige Überarbeitung Nächste Überarbeitung | Vorherige Überarbeitung | ||
projekte:eurotwo [2021/01/01 23:51] max |
— (aktuell) | ||
---|---|---|---|
Zeile 1: | Zeile 1: | ||
- | {{: | ||
- | |||
- | ====== EuroTwo CPU ====== | ||
- | |||
- | Contact: [[user: | ||
- | |||
- | Projectstatus: | ||
- | |||
- | Documentation: | ||
- | |||
- | {{: | ||
- | |||
- | ==== Status ==== | ||
- | === 2021-01-02 === | ||
- | I made a bunch of power cables today. Also I ordered a lot of screws and other stuff. Hopefully tomorrow my board will arrive! | ||
- | |||
- | {{: | ||
- | |||
- | === 2020-12-31 === | ||
- | I soldered 5 more MUXs. Also I ordered ~100 new PCBs. Distributors, | ||
- | |||
- | {{: | ||
- | |||
- | === 2020-10-28 === | ||
- | I tried a different setup of the logo illumination by using two PCBs. I sanded the backside of the first PCB and assembled the LED in the other direction on the second one. This look much smoother and better! | ||
- | |||
- | {{: | ||
- | |||
- | === 2020-10-18 === | ||
- | Testing worked fine. Design looks nice. | ||
- | |||
- | {{: | ||
- | |||
- | === 2020-08-10 === | ||
- | I designed a testing board with a SN754410 H-Bridge driver for testing. I can test 4 outputs and 4 inputs per testing board easily with an Arduino now. The SN754410 is still in delivery and will get assembled later. [[https:// | ||
- | |||
- | {{: | ||
- | |||
- | === 2020-08-01 === | ||
- | My automated long term test is up and running. 1000 test-iterations per bit. Tuned the loading speed of the C (adding 100 Ohms), added diodes (1N4007) and tuned the holding voltage of the relais better by adding 100 Ohms. | ||
- | |||
- | {{: | ||
- | |||
- | === 2020-06-28 === | ||
- | Fixed the "4-Bit Register rev2" board. The board is fully functional but has some drawbacks. You need to scratch away 8 traces on the board and solder 8 short wires on it. | ||
- | |||
- | The fixes for rev3 are: | ||
- | * Cs were not aligned correctly to matching relais. Nobody will see this but still, it is not as intended! Fixed in rev3 | ||
- | * There is a mistake at the store relays. That is why you need to scratch traces. Fixed in rev3 | ||
- | * Rev2 is unable to select between rising and falling edge. This is fixed in rev3 by a jumper | ||
- | * B.Mask is under the LED-Indicator on the back, that is why the light is not as bright as intended. Fixed in rev3. | ||
- | * Numbering of the LEDs would be helpful. Fixed in rev3. | ||
- | |||
- | === 2020-06-18 === | ||
- | The PCBs for the 4Bit Register and the Logo did arrive. I assembled them successfully. I'm now waiting for the new Relays HK19F for the final test of the registers. In the Logo-PCB there was a little mistake but I succeed fixing it by scraping away two traces. | ||
- | |||
- | {{: | ||
- | |||
- | {{: | ||
- | |||
- | ===== Documentation ===== | ||
- | |||
- | ==== Downloads ==== | ||
- | * {{ : | ||
- | * {{ : | ||
- | * {{ : | ||
- | |||
- | |||
- | ==== Sizes/ | ||
- | {{: | ||
- | |||
- | * Holes for signals: 2_2mm vias or pads | ||
- | * Holes for currents: 3.2 | ||
- | * GND on top holes | ||
- | * +5V on bottom holes | ||
- | |||
- | ==== Boards ==== | ||
- | * 2x FullAdder / 4x HalfAdder | ||
- | * 4x Controlled Inverter [[projekte: | ||
- | * 9 Bit AND | ||
- | * 4 Bit Register | ||
- | * MUX 1-4,1-16, DEC 1-4,1-16, 4 Bit MUX 1-4 | ||
- | * Clock | ||
- | * RAM | ||
- | * ROM | ||
- | * Logo | ||
- | |||
- | ---- | ||
- | |||
- | === Logo === | ||
- | This board is made of **120** LEDs just for this board. It is the projectlogo with through-pcb illumination. | ||
- | |||
- | {{: | ||
- | |||
- | |||
- | == Schematics == | ||
- | * //left// | ||
- | |||
- | ---- | ||
- | == BOM == | ||
- | |||
- | ^ Designator ^ Package ^ Quantity ^ Designation ^ | ||
- | | D* | LED_1206_3216 | 120 | blue at 16mA, 5V | | ||
- | | R* | R_0603_1608 | 120 | 330R | | ||
- | | C1,C2 | CP_Elec_6.3x5.4 | 2 | 47uF | | ||
- | | C3,C4,C5 | C_0805_2012 | 3 | 100nF | | ||
- | |||
- | |||
- | ---- | ||
- | |||
- | |||