Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen gezeigt.
Beide Seiten, vorherige Überarbeitung Vorherige Überarbeitung Nächste Überarbeitung | Vorherige Überarbeitung Nächste Überarbeitung Beide Seiten, nächste Überarbeitung | ||
projekte:eurotwo [2020/04/28 22:37] max [Downloads] |
projekte:eurotwo [2020/06/28 17:39] max |
||
---|---|---|---|
Zeile 2: | Zeile 2: | ||
====== EuroTwo CPU ====== | ====== EuroTwo CPU ====== | ||
+ | |||
+ | Latest information are listed [[projekte: | ||
{{ : | {{ : | ||
Zeile 11: | Zeile 13: | ||
===== Arrangement ===== | ===== Arrangement ===== | ||
- | {{ : | + | |
===== Boards ===== | ===== Boards ===== | ||
- | * 1 Bit Full Adder [[projekte: | + | * 2x FullAdder / 4x HalfAdder |
- | * 4 Bit Controlled Inverter [[projekte: | + | * 4x Controlled Inverter [[projekte: |
* 9 Bit AND | * 9 Bit AND | ||
- | * Register 2 Bit | + | * 4 Bit Register |
- | * MUX 3 Select Bits, 1 Data Bit | + | * MUX 1-4,1-16, DEC 1-4,1-16, 4 Bit MUX 1-4 |
- | * DEC 1 Select Bit, 4 Data Bits | + | |
- | * Counterregister 2 Bits | + | |
* Clock | * Clock | ||
- | * 8 Bit Monitor | + | * RAM |
- | * 1 Page RAM | + | |
* ROM | * ROM | ||
* Logo | * Logo | ||
- | |||
- | |||
- | ==== 1Bit-FullAdder ==== | ||
- | The 1Bit-FullAdder sums 3 (// | ||
- | |||
- | {{ : | ||
- | |||
- | Therefore 8 relays are used. I know I can build it from 6. But for didactic reason I decided to use 8. For details see the schematic. | ||
- | |||
- | {{ : | ||
- | |||
- | === Schematic === | ||
- | * {{ : | ||
---- | ---- | ||
- | === BOM === | ||
- | ^ Designator ^ Package ^ Quantity ^ Designation ^ | ||
- | | D7, | ||
- | | R30, | ||
- | | D14, | ||
- | | R4, | ||
- | | C1,C2 | CP_Elec_6.3x5.4 | 2 | 47uF | | ||
- | | C3,C4,C5 | C_0805_2012 | 3 | 1000nF Keramik | | ||
- | | K1, | ||
- | ---- | + | ==== Logo ==== |
- | + | This board is made of **120** LEDs just for this board. It is the projectlogo with through-pcb illumination. | |
- | ==== 4Bit-Controlled-Inverter | + | {{ : |
- | The 4Bit-Controlled-Inverter | + | |
- | {{ : | ||
=== Schematics === | === Schematics === | ||
- | * {{ : | + | * //left// |
---- | ---- | ||
Zeile 65: | Zeile 40: | ||
^ Designator ^ Package ^ Quantity ^ Designation ^ | ^ Designator ^ Package ^ Quantity ^ Designation ^ | ||
- | | D1, | + | | D* | LED_1206_3216 | 120 | blue at 16mA, 5V | |
- | | R1, | + | | R* | R_0603_1608 | 120 | 330R | |
| C1,C2 | CP_Elec_6.3x5.4 | 2 | 47uF | | | C1,C2 | CP_Elec_6.3x5.4 | 2 | 47uF | | ||
| C3,C4,C5 | C_0805_2012 | 3 | 100nF | | | C3,C4,C5 | C_0805_2012 | 3 | 100nF | | ||
- | | D8, | ||
- | | K1, | ||
- | |||
---- | ---- | ||
- | ==== Logo ==== | ||
- | This board is made of **120** LEDs just for this board. It is the projectlogo with through-pcb illumination. | ||
- | {{ : | ||
+ | ==== Status ==== | ||
+ | === 2020-06-28 === | ||
+ | Fixed the "4-Bit Register rev2" board. The board is fully functional but has some drawbacks. You need to scratch away 8 traces on the board and solder 8 short wires on it. | ||
- | === Schematics === | + | The fixes for rev3 are: |
- | * //left// | + | * Cs were not aligned correctly to matching relais. Nobody will see this but still, it is not as intended! Fixed in rev3 |
+ | * There is a mistake at the store relays. That is why you need to scratch traces. Fixed in rev3 | ||
+ | * Rev2 is unable to select between rising and falling edge. This is fixed in rev3 by a jumper | ||
+ | * B.Mask is under the LED-Indicator on the back, that is why the light is not as bright as intended. Fixed in rev3. | ||
+ | * Numbering of the LEDs would be helpful. Fixed in rev3. | ||
- | ---- | ||
- | === BOM === | ||
- | ^ Designator ^ Package ^ Quantity ^ Designation ^ | ||
- | | D* | LED_1206_3216 | 120 | blue at 16mA, 5V | | ||
- | | R* | R_0603_1608 | 120 | 330R | | ||
- | | C1,C2 | CP_Elec_6.3x5.4 | 2 | 47uF | | ||
- | | C3,C4,C5 | C_0805_2012 | 3 | 100nF | | ||
+ | === 2020-06-18 === | ||
+ | The PCBs for the 4Bit Register and the Logo did arrive. I assembled them successfully. I'm now waiting for the new Relays HK19F for the final test of the registers. In the Logo-PCB there was a little mistake but I succeed fixing it by scraping away two traces. | ||
- | ==== MUX 1-4 ==== | ||
- | {{ : | ||
- | === Schematics === | + | {{ :projekte:photo_2020-06-18_15-25-33.jpg? 400 |}} |
- | * {{ :projekte:mux-1-4_rev1.pdf |}} | + | |
- | ==== DEC 3 SelectBits ==== | + | |
- | {{ :projekte:dec.png?400 |}} | + | {{ :projekte:photo_2020-06-18_15-25-30.jpg? 400 |}} |
- | === Schematics === | ||
- | * {{ : | ||
- | |||
- | ---- |